Difficulty

Easy

Steps

8

Time Required

                          15 minutes

Sections

1

  • Realigning 12-Inch Bionaire Fan Metal Coil
  • 8 steps

Flags

0

  • BackFan

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

What you need

Step 1

              Realigning 12-Inch Bionaire Fan Metal Coil
  • Unlock all of the tabs holding the fan cage together.
  • Carefully pull off the cage.

Unlock all of the tabs holding the fan cage together.

Carefully pull off the cage.

1024

Step 2

  • Using a Phillips #2 screwdriver, untighten the 1/4’’ screw that is located underneath the fan blade.
  • Blade may be sharp so watch out!
  • Cautiously remove the blade from the hinge.
  • Put the screws in a cup so you don’t lose them!

Using a Phillips #2 screwdriver, untighten the 1/4’’ screw that is located underneath the fan blade.

Blade may be sharp so watch out!

Cautiously remove the blade from the hinge.

Put the screws in a cup so you don’t lose them!

Step 3

  • Rotate the black cap counter-clockwise to disconnect it from the back fan cage.
  • Pull off the back cage from the engine holder.

Rotate the black cap counter-clockwise to disconnect it from the back fan cage.

Pull off the back cage from the engine holder.

Step 4

  • Working with the Phillips #2 screwdriver, loosen the 1/4’’ center hinge screw from the metal base.

Working with the Phillips #2 screwdriver, loosen the 1/4’’ center hinge screw from the metal base.

Step 5

  • Using the Phillips #2 screwdriver, separate the wire holder from the back of black cover by removing the two 1/8’’ screws.

Using the Phillips #2 screwdriver, separate the wire holder from the back of black cover by removing the two 1/8’’ screws.

Step 6

  • Pull of the black knob by rotating the knob counter-clockwise.
  • Pull down the black cover all the way.
  • The coil may pop out after removing the cover.

Pull of the black knob by rotating the knob counter-clockwise.

Pull down the black cover all the way.

The coil may pop out after removing the cover.

Step 7

  • Take out the gold metal spring.
  • Realign the metal coil into designated space.
  • Push the coil in with some force so it rests perfectly in the space.
  • To make placing the coil back in more easier, use the screwdriver!

Take out the gold metal spring.

Realign the metal coil into designated space.

Push the coil in with some force so it rests perfectly in the space.

To make placing the coil back in more easier, use the screwdriver!

Step 8

  • Align the end of the metal coil into the same hole the black wire comes out of in the black cover from step 6.
  • This can be a frustrating step. Be patient!

Align the end of the metal coil into the same hole the black wire comes out of in the black cover from step 6.

This can be a frustrating step. Be patient!

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      3 other people completed this guide.

Author

                                      with 2 other contributors 


                    Hemish Patel

Member since: 09/29/2015

231 Reputation

                                      1 Guide authored                  



                       Badges:
                       5







                                                        +2 more badges

Team

                       Cal Poly, Team 10-3, Green Fall 2015                        

                                                  Member of Cal Poly, Team 10-3, Green Fall 2015 



                    CPSU-GREEN-F15S10G3                     


                                            4 Members                     


                                            4 Guides authored

Chris - Jan 26, 2017

Reply

I have a fan It hum I have to spin the blade for it to start spin