Difficulty
Moderate
Steps
14
Time Required
15 - 30 minutes
Sections
3
- Razer Naga Trinity Disassembly
- 7 steps
- Scroll Wheel Housing
- 5 steps
- LK-E5 Optical Encoder
- 2 steps
Flags
0
BackRazer Naga Trinity
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Razer Naga Trinity Disassembly
- Remove the interchangeable side plate.
Remove the interchangeable side plate.
1024
Step 2
- Remove the mouse’s feet using the opening pick.
Remove the mouse’s feet using the opening pick.
Step 3
- Remove the four 6mm screws by using a JIS #1 screwdriver.
Remove the four 6mm screws by using a JIS #1 screwdriver.
Step 4
- Separate the top mouse housing from the bottom mouse housing using the opening pick.
- Be careful not to tug too hard on the ribbon connector.
Separate the top mouse housing from the bottom mouse housing using the opening pick.
Be careful not to tug too hard on the ribbon connector.
Step 5
- Unlock the ribbon connector that is held down by the main board clips using the spudger’s pointed end.
Unlock the ribbon connector that is held down by the main board clips using the spudger’s pointed end.
Step 6
- Remove the side housing using the opening pick.
Remove the side housing using the opening pick.
Step 7
- Remove the top housing LED 3-Pin connector that is near the main board.
Remove the top housing LED 3-Pin connector that is near the main board.
Step 8
Scroll Wheel Housing
- Remove one 4mm black Phillips #000 screw from the left side of the mouse holding the scroll wheel LED controller board.
- Then pull the LED controller board upwards and out.
Remove one 4mm black Phillips #000 screw from the left side of the mouse holding the scroll wheel LED controller board.
Then pull the LED controller board upwards and out.
Step 9
- Pry and remove the scroll wheel feedback bar from its hold-down clips using the hook end of a halberd spudger.
Pry and remove the scroll wheel feedback bar from its hold-down clips using the hook end of a halberd spudger.
Step 10
- Remove the scroll wheel feedback bar from the scroll wheel by holding down the spring and using angled tweezers to remove it from its placement.
Remove the scroll wheel feedback bar from the scroll wheel by holding down the spring and using angled tweezers to remove it from its placement.
Step 11
- Remove the scroll wheel optical encoder 3-pin connector from the main board by wiggling the connector upwards.
Remove the scroll wheel optical encoder 3-pin connector from the main board by wiggling the connector upwards.
Step 12
- Using the opening tool, pry the black bracket holding the scroll wheel in place backwards until the scroll wheel housing pops out.
Using the opening tool, pry the black bracket holding the scroll wheel in place backwards until the scroll wheel housing pops out.
Step 13
LK-E5 Optical Encoder
- Remove the scroll wheel from the scroll wheel housing using the opening tool.
Remove the scroll wheel from the scroll wheel housing using the opening tool.
Step 14
- Remove the scroll wheel optical encoder from the scroll wheel.
Remove the scroll wheel optical encoder from the scroll wheel.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
One other person completed this guide.
Author
with 3 other contributors
Alexandros Andreou
Member since: 09/16/2019
640 Reputation
3 Guides authored
Badges:
13
+10 more badges
Team
Embry-Riddle Aeronautical University, Team S6-G2, Salas Fall 2019
Member of Embry-Riddle Aeronautical University, Team S6-G2, Salas Fall 2019
ERAU-SALAS-F19S6G2
4 Members
6 Guides authored
Daniel - Nov 24, 2021
Reply
Where can we buy a replacement from?
